June 17, 2016
Common stalk borer eggs have hatched and scouting should begin when 1,300-1,400 degree days have accumulated. This is when larvae start moving into corn and other crops. Stalk borer growth is based on accumulated degree days since January 1, using a base of 41°F.
Stalk borer damage in corn commonly is confined to plants in the first few rows near field margins, fence rows, grass terraces and waterways. In addition to attacking corn, stalk borers attack over 100 other species of plants, including ornamentals, garden vegetables, broadleaf weeds and grasses. They may feed on soybeans as well, but they are not an economically important pest in soybeans.
Understanding the common stalk borer life cycle and behavior is critical to selecting management practices to reduce damage in corn.
Stalk borer life cycle
Female stalk borer moths lay their eggs primarily on grasses such as smooth brome or ragweed in late summer and early fall. Egg-laying sites usually are in fence rows, terraces and waterways, but can be found throughout a field if preferred hosts are available. Eggs overwinter and hatch in late April or early May. Larvae bore into the stalks of grasses or other hosts such as ragweed, and begin feeding. As they become larger or if the plants are mowed or burned down with herbicides, the stalk borers migrate into adjacent corn plants to complete their development. In some cases, if an appropriate weed host is not available when eggs hatch, stalk borers may begin feeding directly on corn.
Corn between the 2- and 8-leaf stages can be attacked by the migrating stalk borer larvae. Larvae develop through seven to 10 instars, or stages, in about 10 weeks. Pupation occurs in the soil and moths emerge in August, September, and early October. There is a single generation each year.
Stalk borer identification
Common stalk borer larvae are distinctive in appearance. Young larvae are brownish-purple and have three prominent longitudinal white stripes at the front and rear ends of the body. The stripes are interrupted at mid-body by a solid dark purple to black area on the third thoracic segment and first three abdominal segments. Fully grown larvae do not have these characteristic markings and are uniformly dirty gray (Figure 1b). Fully grown larvae can be 1½-2 inches long.
Stalk borer damage
Stalk borer larvae injure corn plants in June and early July. They feed on leaves in the whorl and then tunnel into the stalk, or they burrow into the base of the plant and tunnel up through the center of the stalk. Leaf feeding alone does not cause economic damage.
Tunneling into the stalk can result in deformed or stunted plants that may not produce an ear. Severely damaged plants can die. Plants attacked at earlier growth stages tend to be more severely injured. A single stalk borer larva may attack more than one plant if the first plant does not support the larva as it increases in size.
Damage caused by feeding in the whorl will first appear as irregular rows of holes in the unfolding leaves. These irregular rows of holes will be much larger and more ragged than those caused by whorl-feeding of first generation European corn borer larvae. In severe cases an infested plant will have a very ragged appearance, with abnormal growth habits such as twisting, bending over, or stunting. If the feeding injury to the central part of the plant is severe enough, the whorl will appear dead while the outer leaves will be green and apparently healthy. This condition is commonly called "dead heart."
Common corn stalk borer management
Any weed control method that helps eliminate grasses will reduce the number of potential stalk borer egg-laying sites, reducing the probability of stalk borer damage the next year. Control of grassy weeds is important to keep stalk borer problems from increasing year to year.
Planting date may have some influence on the degree of injury from common stalk borers. Since smaller plants are more heavily damaged, earlier planting may allow corn to outgrow the most severe damage.
Using GDDs to predict development
Stalk borer hatch and migration to new hosts can be predicted using growing degree days (GDD). Based on research at Iowa State University, stalk borer egg hatch begins at about 575 GDD and ends at 750 GDD. Begin scouting corn when 1,300-1400 GDD have accumulated. This corresponds with the beginning of larvae moving out of grassy hosts. Determine the need for treatment when 1,400-1,700 GDD have accumulated.
This week's map indicates that stalk borer eggs have hatched across most of the state. Be ready to scout for larvae when 1,300-1,400 degree day accumulation has occurred.
Sampling and economic injury levels
Check corn plants bordering grassy areas to determine the percentage of plants with stalk borer injury when 1,300-1,400 degree days (41°F base) have accumulated since January 1 (Figure 3). Examine several sets of 10 plants. Look for feeding damage and dissect damaged plants to see if live larvae are present. If weedy grasses were common throughout the field in the previous year, the whole field may need to be scouted for common stalk borers. Use the information in Table 2 to determine the economic injury level.
To be effective, insecticides must be applied before common stalk borer larvae have entered the stalk. In cases where stalk borers begin feeding on grassy weeds or other vegetation in field edges, control is most effective if timed between 1,400 and 1,700 degree days (base 41°F), which corresponds to the first half of the period when stalk borers are migrating from weedy hosts into corn. If the infestation is restricted to the field margin, use a border treatment.
Insecticides may be mixed with fast-acting herbicides being used to burn down early season weeds, or applied several days after use of slower-acting herbicides. Check the label for compatibility of different insecticide and herbicide mixtures.
A variety of foliar insecticides are effective against common stalk borers in corn. See the 2016 Guide to Weed Management in Nebraska with Insecticide and Fungicide Information (EC130) or the insecticide label information for labeled insecticides, their rates, and restrictions.
Several available Bt corn hybrids provide control or suppression of common stalk borer larvae. The label term "suppression" indicates that a lower level of mortality is expected than for insects labeled for control. (See Handy Bt Trait Table for a list of available hybrids.)
For more information on stalk borer biology and management, see
Stalk Borer Ecology and Integrated Pest Management in Corn, a 2010 article by Marlin Rice and Paula Davis in the Journal of Integrated Pest Management
Common Stalk Borer in Corn, UNL NebGuide G521.
You May Also Like
Current Conditions for
Enter a zip code to see the weather conditions for a different location.
Pros and cons of H-2A guest farmworkersNov 30, 2023
Market expectations: What's on the horizon for grain and livestock?Nov 22, 2023
18 gifts for the farmer on your listNov 27, 2023