Iowa State University Extension field agronomists Meaghan Anderson and Rebecca Vittetoe previously posted an article on the ISU Integrated Crop Management on evaluating corn stands. Many of the same issues are important when evaluating soybean stands.

A very small percent of the soybean crop had emerged in Iowa at the end of last week. As the crop continues to emerge across the state, checking the emergence of the soybeans and identifying any potential issues in the field will be important. Anderson and Vittetoe offer the following information and recommendations.

Taking stand counts in soybeans is similar to that of corn. A soybean stand is not as critically linked to yield as with corn; however, early-season stand counts are important to evaluate the germination and emergence of the planted soybeans.

In addition, while doing the stand counts, look for issues that may require management, such as diseases, insects or other problems that could persist through the growing season. Several helpful methods are available to estimate soybean stand.

4-step process

The traditional method of counting soybean stands involves four steps:

1. Measurements. Measure a 1,000th of an acre based on row width (Table 1). In 30-inch row soybeans, measure out a length of 17 feet, 5 inches (1 transect) and count the number of plants within the transect. 

2. Multiple transects. Repeat this process in multiple, representative transects across the field. Typically, at least six to 10 arbitrary transects per field are suggested. Do not intentionally avoid areas with missing plants. But if one stand count seems unusually low or different than other counts, keep that one separate and make note of it.

3. Calculations. Average the number of plants per transect and multiply the average number of plants by 1,000 to obtain the estimated plant population per acre. 

4. Health checkup. Dig up seedlings and check for symptoms of problems such as seed rots and seedling blights and herbicide injury. Also, look for insect issues like seedcorn maggot, black cutworm, true armyworm, or even a non-insect pest like slugs.

Also, look for planter issues (seed depth or missing plants). If plants are missing entirely, check to see if seeds are present where the plants should be; soybeans may emerge over a period of days to weeks, so plant stands may improve if counts are taken very early.

Alternative methods

It is not uncommon to see 15-inch, 10-inch, or sometimes even 7.5-inch row soybeans, especially if planted with a drill. Taking stand counts using the traditional method (as described above) can be arduous if soybeans are planted in narrow rows, so an alternative method may be more conducive to quickly getting stand count estimates.

Counting plants per foot of row. Estimate the total plant stand by counting soybeans in an individual foot of row using Table 2. Like other methods, multiple transects are necessary to get a representative estimate of the stand across a field. These counts can be done more quickly than measuring a 1,000th of an acre but may require more counts if stands are particularly uneven.

Hula hoop method.  To use this method, toss a hula hoop to arbitrarily select an area for a stand count. Count the number of plants inside the hula hoop and multiply the number of plants by a factor to estimate the number of plants per acre (Table 3). 

With this method, count the number of plants inside the hula hoop diameter and take the number of plants times a multiplication factor based on the diameter of the hula hoop. If a hula hoop does not have the exact diameter of those listed in the table below, determine the estimated stand by using this equation: population = plants counted / (3.14 * hoop radius * hoop radius / 43,500)]. 

There are also tables available with plant populations already calculated based on the number of plants and hula hoop diameters.

Average the stand counts and divide by the total number taken to determine an estimated average plant stand. Like the traditional method, take multiple counts at various locations (at least 10 arbitrary locations) in the field. This method is often easier to get arbitrary counts but may require more counts than the traditional method to get an accurate idea of stand if the population is uneven or seeding rates were low. 

Remember, if one count doesn’t seem to fit the other counts, keep that number separate and make note of where that area is at in the field. Investigate to figure out what may have reduced the stand in that area. Consider how widespread the issue is and whether it has a pattern or is seemingly random.

Final stands are often at least 10% to 20% lower than the original seeding rate. With early-season soybean planting, a final stand of 100,000 evenly spaced plants is desired, but soybeans have a significant ability to branch and yield well even in thinner stands.

Replant considerations

If the emerged soybean population is significantly lower than expected, replanting or, more likely, “thickening up” soybeans may be considered. Unlike in corn, rarely do soybean fields require replanting, but planting additional soybeans on an offset pattern (typically angled or perpendicular) from the original rows is usually sufficient to improve a disappointing stand. 

Due to the soybean plant’s growth habit and reproductive capabilities, soybeans can co-exist at different crop development stages without issue.

To determine whether replanting is likely to be of benefit, start by estimating the yield potential of the current stand for the original planting date using Soybean Replant Decisions, PM 1851. In general, replanting should be considered if uniform stands are less than 75,000 plants per acre when planted prior to mid-May, or less than 50,000 to 60,000 plants per acre when planted late May into June. Soybeans can compensate for low stands through increased branching and pod set.

Other factors to consider

Be sure to factor in replant costs like fuel, seed, and time and labor. Also, if you decide to replant, other possible costs include seed treatments and herbicide applications. Additional factors to consider:

Soybean seed treatments. They are often not necessary for replanted soybeans due to warmer soils at the time of planting. However, you should consider using a fungicide seed treatment if the field is prone to seedling diseases.

Weed woes. Low or uneven soybean populations may be more susceptible to weed issues due to lack of early-season suppression from the plant canopy, so additional postemergence herbicide may be necessary. Additionally, reference herbicide labels for any products already applied to the field to be certain residual products do not disallow replanting.

Timing adjustments. Maturity selection, seeding rate and row spacing may all need adjustment due to the shorter time frame to harvest and lack of competitive ability of late-planted soybeans. If already planting a well-adapted soybean variety to the area, do not change maturity selection unless replanting occurs in late June, but do consider increasing seeding rate or narrowing row spacing to allow for more competition with weeds.

Taking the time to determine estimated stand counts after crop emergence is no simple effort. As more of the soybean crop emerges, this practice, as well as checking the plants for potential insect, disease or herbicide issues, will be key to making management adjustments now or understanding problems later in the growing season.

The steps outlined and explained in this article will aid decision-making in identifying possible issues and determining if replanting or “thickening up” soybeans is necessary. Also, contact your local Extension field agronomist if you have any questions.

Source: ISU, which is responsible for the information provided and is wholly owned by the source. Informa Business Media and its subsidiaries aren’t responsible for any of the content contained in this information asset.