is part of the Division of Informa PLC

This site is operated by a business or businesses owned by Informa PLC and all copyright resides with them. Informa PLC's registered office is 5 Howick Place, London SW1P 1WG. Registered in England and Wales. Number 8860726.

  • American Agriculturist
  • Beef Producer
  • Corn and Soybean Digest
  • Dakota Farmer
  • Delta Farm Press
  • Farm Futures
  • Farm Industry news
  • Indiana Prairie Farmer
  • Kansas Farmer
  • Michigan Farmer
  • Missouri Ruralist
  • Nebraska Farmer
  • Ohio Farmer
  • Prairie Farmer
  • Southeast Farm Press
  • Southwest Farm Press
  • The Farmer
  • Wallaces Farmer
  • Western Farm Press
  • Western Farmer Stockman
  • Wisconsin Agriculturist
Corn+Soybean Digest

Glyphosate Nonperformance Issues And Glyphosate-Resistant Biotypes

Glyphosate-resistant biotypes of giant and common ragweed and common waterhemp have been confirmed in Minnesota and are listed on the International Survey of Resistant Weeds Web site. Both species appear to be resistant to approximately four-times the labeled use rate of glyphosate (4X).

In the short timeframe presented to us during the growing season, separating glyphosate nonperformance due to resistant weed biotypes from other factors is an inexact and qualitative process, but a quick response could help reduce the spread of glyphosate-resistant weeds and set up long-term management plans.

A long-term plan would likely include chemical diversification that can provide consistent economic performance to the grower who uses Roundup Ready technology and can help to reduce the probability of glyphosate-resistant weeds diminishing the economic value of this technology.

Whatever the cause, the short-term goal is clear: weed control. Determining the presence of surviving plants early in the growing season allows time for successful control. Therefore, begin the process by scouting your fields 10-14 days after your first glyphosate application.

Glyphosate-resistant weed biotypes are difficult to detect because of their low level of resistance and the numerous other factors commonly associated with nonperformance such as:

  • Misapplication – e.g. using too low of a rate for a given weed size.
  • Improper timing – e.g. application on weed sizes exceeding label recommendations.
  • Weed flushes after application of glyphosate, a nonresidual herbicide.
  • Cold weather conditions several days before or after application.
  • Rainfall shortly after application.
  • Dust or water with a high concentration of dissolved salts preventing absorption

Points to consider in assessing the likelihood of glyphosate-resistant biotypes include the following:

  • Recognize glyphosate-resistant biotypes early. Scout your fields approximately 10-14 days after your first glyphosate application to detect weed escapes. Look for the presence of a single surviving species, generally growing in patches.
  • If more than one species is not controlled – especially if grass weeds are present – consider the factors other than resistance that might have affected nonperformance. Note: multiple resistant weed species are possible as is the presence of a more glyphosate-tolerant species such as common lambsquarters.
  • Is the uncontrolled weed species listed on the glyphosate label as being controlled at the weed size and herbicide rate that you applied? Reduced rates and application to larger weeds can contribute to nonperformance issues without the weed biotypes being resistant.
  • Some weed species have always been difficult to consistently control in glyphosate-dominated cropping systems. Examples include: Asiatic dayflower, wild buckwheat and yellow nutsedge. Common lambsquarters control is more consistent when treated weeds are less than 2 in. tall and during periods of warm and sunny conditions.
  • Did the glyphosate application fail to control the same weed species in the same area of the field in previous years? Resistance development is difficult to determine at low populations, however, repetition of glyphosate failure is an indicator of resistance.
  • Do field histories indicate extensive use of the same herbicide for several years?
  • Overreliance on a single herbicide is a primary contributor to selection for herbicide resistant weeds.
  • Do surrounding fields extensively treated with glyphosate indicate a similar level of nonperformance? Over time, herbicide-resistant weeds can spread via harvest equipment, wind or wildlife to surrounding fields.
  • For the weed species in question, do you see a range of symptoms from dead plants to severely injured to stunted with shortened internodes but with a healthy meristem? Genetic diversity within a resistant weed population often produces a range of herbicide-induced injury responses.

One of the short-term key benefits for differentiating the likelihood of glyphosate-resistant weeds from other issues of nonperformance is to prevent the remedial treatment from being a repeat application of glyphosate only at a higher rate. The application of more glyphosate on glyphosate-resistant biotypes accomplishes nothing but could result in satisfactory performance if nonperformance was due to some of the other factors listed previously.

For effective weed control, alternative herbicides should be applied at their labeled rates (don’t cut rates) on small weeds and to prevent crop injury, the maximum-growth-stage restrictions should be adhered to (see examples below). Inter-row cultivation is also an effective option.

Corn Herbicide – Maximum Growth Stage
Callisto: 30 in. or V8
Hornet: 20 in. or V6
Impact: Up to 45 days before harvest
Laudis: V8
Liberty: LL corn only; 24 in. or V7
Status: 36 in. or V10

Soybean Herbicide – Maximum Growth Stage
Cobra: R6
Flexstar: Prior to bloom
FirstRate: Prior to 50% flowering

For more details on the biology and management of the glyphosate-resistant weed species mentioned, go to Glyphosate, Weeds and Crops.

Hide comments


  • Allowed HTML tags: <em> <strong> <blockquote> <br> <p>

Plain text

  • No HTML tags allowed.
  • Web page addresses and e-mail addresses turn into links automatically.
  • Lines and paragraphs break automatically.